WTB Hub User’s Manual
for all WTB hubs
V 15
NOTE TO RETAILERS: If you are installing this component for your customer, please make sure that
this User’s Manual is passed along to the customer after you use it.
GI3-0309
Thank you for the confidence you have shown in WTB by selecting one of our products. We appreciate
your business, and your satisfaction is important to us.
Because we would like to make sure that you get the best performance and longest service life from any
WTB product you use, we urge you to read these instructions before you assemble or install your new WTB
components.
And if you have any questions or problems, or feel you do not understand something about the product, its
installation or its use, please talk to any WTB dealer or check with us at wtb.com.
GI1-0508-1
IMPORTANT NOTE: This WTB user’s manual for this specific component on your bicycle is not a
substitute for all the safety and use information contained in the owner’s manual that was supplied
with your bicycle. If you do not have such an owner’s manual, contact the bicycle's manufacturer or
retailer for a copy. To the extent that your bicycle user’s manual and this component part user’s
manual conflict as to the use of this specific WTB component, this WTB user’s manual should be
followed. If you are unsure about the resolution of a conflict between this manual and any other
manual or set of instructions, please consult your local bicycle retailer.
GI2-0309
1. Before you start
GENERAL WARNING:
The fact that you selected one or more WTB components for your bike indicates that you are
probably a rider of above average experience; but don’t allow that to lull you into complacency. No
matter how experienced you are as a cyclist, do not fail to read this WARNING or to carefully follow the
instructions below.
Technological advances have made bicycles and bicycle components more complex, and the pace
of innovation is increasing. Many bicycle component installation, service and repair tasks require
special knowledge and tools. Improper installation, adjustment or service may result in damage to the
component or component failure.
All WTB products should be installed by a qualified bicycle mechanic using appropriate
professional tools. WTB assumes no liability for products which are improperly installed, assembled or
configured.
When installing WTB components in conjunction with another manufacturer’s components, you
should always follow that manufacturer’s instructions for their components and WTB’s for WTB
components. If there is a conflict, ask your dealer to help you resolve it. WTB assumes no liability for
damage caused by installing other manufacturers’ products.
After any installation, adjustment or repair to your bicycle or components, test your work by taking
a test ride in a controlled environment, away from cars, other cyclists, obstacles or other hazards.
Failure to follow these instructions can result in component failure. Component failure can cause
you to lose control of the bicycle and fall, leading to serious injury or death.
GW2-0508-1
a. Intended Use: This product is not intended for use by children age 12 and under. Check the Intended
Use information for his product on our Web site at wtb.com/tech-catalog-archive to make sure this product is
compatible with how you intend to use it. Also please check the website to make sure you have the most
dropout. The amount of clamping force is controlled by the tension adjusting nut. Turning the tension adjusting
nut clockwise while keeping the open cam lever from rotating increases clamping force; turning it counter-
clockwise while keeping the open cam lever from rotating reduces clamping force. Less than half a turn of the
tension adjusting nut can make the difference between safe clamping force and unsafe clamping force.
WARNING: The full force of the cam action is needed to clamp the wheel securely. Holding the nut
with one hand and turning the lever like a wing nut with the other hand until everything is as tight as
you can get it will not clamp a cam action wheel safely in the dropouts.
b. Installing a WTB Front Wheel with over-center cam action quick release
CAUTION: Be careful not to damage the disc, caliper or brake pads when re-inserting the disc into
the caliper. Never activate a disc brake’s control lever unless the disc is correctly inserted in the
caliper.
(1) Move the cam lever so that it curves away from the wheel (fig.1). This is the OPEN position.
(2) With the steering fork facing forward, insert the wheel between the fork blades so that the axle seats
firmly at the top of the fork dropouts. The cam lever should be on rider’s left side of the bicycle (fig. 1).
(3) Holding the cam lever in the ADJUST position with your right hand, tighten the tension adjusting nut with
your left hand until it is finger tight against the fork dropout (fig. 1).
(4) While pushing the wheel firmly to the top of the slots in the fork dropouts, and at the same time centering
the wheel rim in the fork, move the cam lever upwards and swing it into the CLOSED position (fig. 1). The lever
should now be parallel to the fork blade and curved toward the wheel. To apply enough clamping force, you
should have to wrap your fingers around the fork blade for leverage, and the lever should leave a clear imprint
in the palm of your hand.
NOTE: If the lever cannot be pushed all the way to a position parallel to the fork blade, return the lever to the
OPEN position. Then turn the tension adjusting nut counterclockwise one-quarter turn and try tightening the
lever again.
Securely clamping the wheel with a cam action retention device takes considerable
WARNING:
force. If you can fully close the cam lever without wrapping your fingers around the fork blade for
leverage, the lever does not leave a clear imprint in the palm of your hand, and the serrations on the
wheel fastener do not emboss the surfaces of the dropouts, the tension is insufficient. Open the lever;
turn the tension adjusting nut clockwise a quarter turn; then try again.
(5) Spin the wheel to make sure that it is centered in the frame and clears the brake pads; then squeeze the
brake lever and make sure that the brakes are operating correctly.
c. Removing a WTB Front Wheel with over-center cam action quick release
CAUTION: Disc rotors have sharp edges, and both rotor and caliper can get very hot during use.
Exercise care in touching the rotor or caliper.
(1) Move the cam lever from the locked or CLOSED position to the OPEN position (fig. 1).
(2) Loosen the tension adjusting nut enough to allow removing the wheel from the fork dropouts. You may
need to tap the top of the wheel with the palm of your hand to release the wheel from the front fork.
d. Installing a WTB Rear Wheel
CAUTION: Be careful not to damage the disc, caliper or brake pads when re-inserting the disc into
the caliper. Never activate a disc brake’s control lever unless the disc is correctly inserted in the
caliper.
(1) With a cam action system, move the cam lever to the OPEN position (fig. 1). The lever should be on the
side of the wheel opposite the derailleur and freewheel sprockets.
(2) On a derailleur bike, make sure that the rear derailleur is still in its outermost, high gear, position; then
pull the derailleur body back with your right hand. Put the chain on top of the smallest freewheel sprocket.
(3) On a LaserDisc Single Duty hub, remove the chain from the front sprocket, so that you have plenty of
slack in the chain. Put the chain on the rear wheel sprocket.
(4) Then, insert the wheel into the frame dropouts and pull it all the way in to the dropouts.
(5) On a LaserDisc Single Duty hub, replace the chain on the chainring; pull the wheel back in the dropouts
so that it is straight in the frame and the chain has about 1/4 inches of up-and-down play.
(6) With a cam action system, move the cam lever upwards and swing it into the CLOSED position (fig. 1).
The lever should now be parallel to the seat stay or chain stay and curved toward the wheel. To apply enough
clamping force, you should have to wrap your fingers around the fork blade seat stay or chain stay for
leverage, and the lever should leave a clear imprint in the palm of your hand.
(7) With a Single Duty hub, tighten the fasteners to 10 Nm (90 in. lbs) torque.
NOTE: If, on a cam action system, the lever cannot be pushed all the way to a position parallel to the seat stay
or chain stay, return the lever to the OPEN position. Then turn the tension adjusting nut counterclockwise one-
quarter turn and try tightening the lever again.
Securely clamping the wheel with a cam action retention device takes considerable
WARNING:
force. If you can fully close the cam lever without wrapping your fingers around the seat stay or chain
stay for leverage, the lever does not leave a clear imprint in the palm of your hand, and the serrations
on the wheel fastener do not emboss the surfaces of the dropouts, the tension is insufficient. Open the
lever; turn the tension adjusting nut clockwise a quarter turn; then try again.
(8) Spin the wheel to make sure that it is centered in the frame and clears the brake pads; then squeeze the
brake lever and make sure that the brakes are operating correctly.
e. Removing a WTB Rear Wheel
(1) If you have a multi-speed bike with a derailleur gear system: shift the rear derailleur to high gear (the
smallest, outermost rear sprocket).
If you have a single-speed bike with a WTB LaserDisc Single Duty hub, go to step (3) below.
(2) On a derailleur gear system, pull the derailleur body back with your right hand.
(3) With a cam action system, move the quick-release lever to the OPEN position (fig. 1). With the Single
Duty hub, loosen the fasteners with a 5mm hex wrench (fig. 2); then push the wheel forward or down far
enough to be able to remove the chain from the rear sprocket.
(4) Lift the rear wheel off the ground a few inches and remove it from the rear dropouts.
BPSA-OM#9-2A
3. Maintenance and Repair
WARNING:
Many bicycle component installation, service and repair tasks require special knowledge and tools.
Do not begin any installation, adjustments or service on your bicycle until you have learned from your
dealer how to properly complete it. Improper installation, configuration, adjustment or service may
result in damage to the component or component failure. Component failure can cause you to lose
control and fall.
BPSA-OM9-5
Like any mechanical device, a bicycle and its components are subject to wear and stress. Different
materials and mechanisms wear or fatigue from stress at different rates and have different life cycles.
If a component’s life cycle is exceeded, the component can suddenly and catastrophically fail, causing
serious injury or death to the rider. Creaks, scratches, cracks, fraying and discoloration are signs of
stress-caused fatigue and indicate that a part is at the end of its useful life and needs to be replaced.
While the materials and workmanship of your bicycle or of individual components may be covered by a
warranty for a specified period of time by the manufacturer, this is no guarantee that the product will
last the term of the warranty. Product life is often related to the kind of riding you do and to the
treatment to which you submit the bicycle and its components. The warranty is not meant to suggest
that the bicycle or a component cannot be broken or will last forever. It only means that the bicycle or
component is covered subject to the terms of the warranty.
BPSA-om9-5A
The “useful life” of this component (the time during which the component is safe to ride) will be
reduced if (1) you use it more than the average user; (2) you are heavier than the average rider; (3) the
terrain/roads you ride on is rougher than average; (4) you tend to be harder on components than the
average rider; (5) you fail to follow its installation instructions or maintenance instructions, including
lubrication and adjustment; (6) it must endure more adverse environmental conditions than the
average component (i.e. sweat, corrosive mud, salty beach air etc.); (7) you damage/weaken it in a
crash, jump or through other abuse; (8) you fail to purchase the appropriate model of product for the
type of riding it endures; and/or (9) you race with the component or participate in any other type of
extreme, aggressive riding such as Aggro, Hucking, Freeride, North Shore, Downhill, Jumping, Stunt
Riding, etc. The more factors you meet and the more often they occur, the more this component’s life
will be reduced, however it is impossible to say how much.
Racing (road, mountain or triathlons) places extreme stress on bicycles and their components (like
it does riders) and significantly shortens their usable or “useful” life (the time during which the
component is safe to ride). If you participate in these types of events, the lifetime of the product may
be significantly shortened depending upon the level and amount of racing. The “normal wear” of a
component may differ greatly between competitive and non-competitive uses, which is why
professional level riders often use new bikes and components each season as well as having their
bikes serviced by professional mechanics after each ride. Particular care should be placed in the
regular examination of your bicycle and it’s components to insure your safety.
UL2-0508-1
If you engage in extreme, aggressive stunt or competition riding, you will get hurt, and you
voluntarily assume a greatly increased risk of injury or death.
Not all bicycles, components or equipment are designed for these types of riding, and those that
are may not be suitable for all types of aggressive riding. Check with the bicycle’s or component’s
manufacturer about suitability before engaging in extreme riding.
When riding fast down hill, you can reach speeds achieved by motorcycles, and therefore face
similar hazards and risks. Have your bicycle and equipment carefully inspected by a qualified
mechanic and be sure it is in perfect condition. Consult with expert riders, area site personnel and race
officials on conditions and equipment advisable at the site where you plan to ride. Wear appropriate
safety gear, including an approved full face helmet, full finger gloves, and body armor. Ultimately, it is
your responsibility to have proper equipment and to be familiar with course conditions.
Although many catalogs, advertisements and articles about bicycling depict riders engaged in
extreme riding, this activity is extremely dangerous, increases your risk of injury or death, and
increases the severity of any injury. Remember that the action depicted is being performed by
professionals with many years of training and experience. Know your limits and always wear a helmet
and other appropriate safety gear. Even with state-of-the-art protective safety gear, you could be
seriously injured or killed when jumping, stunt riding, riding downhill at speed or in competition.
BPSA-OM9-2F
a. Maintenance
WTB LaserDisc hubs use sealed bearings and protected mechanisms; but, like anything mechanical, they
are subject to wear and corrosion from moisture, dirt and salt. The best maintenance for your WTB hubs is to
clean them with water and a soft brush or lint-free cloth.
Do not use water under high pressure to blast off dirt and mud. The water could penetrate the seals and
damage the bearings and other metal parts.
Periodically lubricate the threads and cam surfaces on the quick release skewer or the threads on the axle
bolts of the Single Duty hub.
Before each use, check brake wear and operation; spoke tension, rim wear, damage and trueness; and tire
fit, wear, damage and inflation. Spin each wheel slowly and look for any signs of damage: dents, bulges,
cracks, or deformation of the rims. Check spoke tension, by spinning the wheel to make
sure it is true (no side-to-side wobble, no up-and-down hop); by squeezing pairs of
spokes to make sure none are loose or broken; and by plucking each spoke to make sure
they all sound about the same. If you discern a difference in tension when squeezing two
adjoining spokes or in the pitch of the sound of a plucked spoke this may indicate a
significant difference in that spoke’s tension. If in doubt about spoke tension or wheel
trueness, do not ride the bike. Take it to a qualified bicycle mechanic.
With rim brakes, check that the wear indicator on the sidewall braking surface is still
clearly visible.
Before every ride, check the tires for excess wear, cuts in the tread and cuts or
bulges in the sidewall. Check the tire pressure of both tires. The tire’s pressure rating is marked on the
sidewall.
Spoke tensioning and wheel truing is a highly refined skill which requires expensive
CAUTION:
special tools and experience. Do not attempt to tension or true a wheel unless you have the
knowledge, experience and tools needed to do the job correctly.
WH2-0508-1
WARNING: Do not ride a bike with a damaged tire or rim. Riding a damaged tire or rim may lead to
sudden tire deflation or improper braking function. Sudden tire deflation or improper braking function
can cause loss of control, resulting in serious injury or death. Replace damaged tires and rims before
riding the bike.
Never inflate a tire beyond the maximum pressure, or ride a tire with less than the minimum
pressure marked on the tire’s sidewall. Exceeding the recommended maximum or minimum pressure
may cause sudden tire failure. Tire failure can cause loss of control, resulting in serious injury or
death.
TI1-0508-1
b. Service and Repair
We strongly urge you to have any servicing or repair of your WTB components done by a qualified bicycle
mechanic with the appropriate tools, knowledge and experience. If you believe that you are qualified to service,
replace parts or repair a WTB component, please download, read and follow the Service Instructions at
wtb.com/tech/serviceinstructions for the component which you plan to repair.
SE1-0608-2
4. Replacement Parts
WARNING: Use only genuine WTB replacement parts and follow the Service Instructions at
wtb.com. Failure to do so could compromise the safety or performance of the component and result in
component failure.
GI4-0508-1
5. Warranty
WTB products are warranted against defects in materials and workmanship. To read the full current
warranty for your WTB product, see the Warranty section of our Web site, wtb.com/warranty
GI5-0508-1
6. Making a warranty claim
To make a warranty claim, see the Warranty section of our Web site, wtb.com/warranty
GI6-0508-1
7. Contact Information
If you have any questions or problems with any WTB product, please go to wtb.com for help.
GI7-0508-1
8. Disclaimer
The original English language version/meaning of these instructions supercedes all translations. WTB is
not responsible for any errors in translation of these or any product instructions.
GI8-0508-1
© Copyright WTB March 2009
|